Go Back   ISPINE.ORG Forum > Main forums > Abstracts and Articles
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Abstracts and Articles Discuss The effect of different design concepts in lumbar total disc arthroplasty on the ... in the Main forums forums; from: Springerlink.com The effect of different design concepts in lumbar total disc arthroplasty on the range of motion, facet ...

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 12-11-2009, 06:37 PM
Senior Member
 
Join Date: May 2008
Posts: 196
Default The effect of different design concepts in lumbar total disc arthroplasty on the ...

from: Springerlink.com

The effect of different design concepts in lumbar total disc arthroplasty on the range of motion, facet joint forces and instantaneous center of rotation of a L4-5 segment
Journal European Spine Journal
Publisher Springer Berlin / Heidelberg
ISSN 0940-6719 (Print) 1432-0932 (Online)
Issue Volume 18, Number 11 / November, 2009
Category Original Article
DOI 10.1007/s00586-009-1146-y
Pages 1695-1705
Subject Collection Medicine
SpringerLink Date Thursday, September 17, 2009


Hendrik Schmidt1 , Stefan Midderhoff1, Kyle Adkins1 and Hans-Joachim Wilke1

(1) Institute of Orthopaedic Research and Biomechanics, University of Ulm, Helmholtzstrasse 14, 89081 Ulm, Germany


Abstract

Although both unconstrained and constrained core lumbar artificial disc designs are in clinical use, the effect of their design on the range of motion, center of rotations, and facet joint forces is not well understood. It is assumed that the constrained configuration causes a fixed center of rotation with high facet forces, while the unconstrained configuration leads to a moving center of rotation with lower loaded facets. The authors disagree with both assumptions and hypothesized that the two different designs do not lead to substantial differences in the results. For the different implant designs, a three-dimensional finite element model was created and subsequently inserted into a validated model of a L4-5 lumbar spinal segment. The unconstrained design was represented by two implants, the Charité® disc and a newly developed disc prosthesis: Slide-Disc®. The constrained design was obtained by a modification of the Slide-Disc® whereby the inner core was rigidly connected to the lower metallic endplate. The models were exposed to an axial compression preload of 1,000 N. Pure unconstrained moments of 7.5 Nm were subsequently applied to the three anatomical main planes. Except for extension, the models predicted only small and moderate inter-implant differences. The calculated values were close to those of the intact segment. For extension, a large difference of about 45% was calculated between both Slide-Disc designs and the Charité® disc. The models predicted higher facet forces for the implants with an unconstrained core compared to an implant with a constrained core. All implants caused a moving center of rotation. Except for axial rotation, the unconstrained and constrained configurations mimicked the intact situation. In axial rotation, only the Slide-Disc® with mobile core reproduced the intact behavior. Results partially support our hypothesis and imply that different implant designs do not lead to strong differences in the range of motion and the location of center of rotations. In contrast, facet forces appeared to be strongly dependent on the implant design. However, due to the great variability in facet forces reported in the literature, together with our results, we could speculate that these forces may be more dependent on the individual spine geometry rather than a specific implant design.

Keywords Mobile artificial discs - Finite element analysis - Arthroplasty devices - Back pain - Implants
Reply With Quote
Reply

Bookmarks

Tags
arthroplasty, artificial, back pain, devices, disc, facet, finite element analysis, implacts, joint, lumbar, mobile

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 07:36 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.